机加工图纸英语备用教材.doc

机加工图纸英语备用 ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED 未注焊缝均为连续焊 ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm. ALL UNSPECIFIED RADI - R3 未注圆角R3 REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝 CHANNEL 槽钢 RSA 708 角钢 70X70X8 M30X1.5 pitch M30X1.5的锥螺纹 Tackweld 点焊 OD 1/4 outside dimension 1/4的缩写 外径直1/4 75 CRS 尺寸为75 材质为冷轧钢板 410 OPENING REF 410 开口参考尺寸 40 REF 尺寸为40,参考值 2.5 BSP 2.5” 圆锥管螺纹 2.5 BSPT HEXAGON 2.5” 六角圆锥管螺纹(即对丝) 30x2.5 FLAT BAR 30X2.5?扁钢 TYP 2 POSNS 2处 11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH. 总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明) FEMALE: 内扣(母扣) MALE: 外扣(公扣) 偏心轴 eccentric shaft 销轴 PIN 开口销 COTTER PIN 螺杆 screw 紧定螺钉 SET SCREW 圆螺母 ROUND NUT 内六角螺钉 SOCKET HEAD CAP SCREW 六角螺钉 HEX HD SETSCREW 六角螺栓 HEX HD BOLT? 挡圈 closing ring 弹性挡圈 circlip 轴承隔套 distance sleeve of axletree 轴承 axletree 深沟球轴承 DEEP GROOVE BALL BEARING 无扣长 non-buckle longth 弹簧 SPRING 吊环螺钉 LIFTING EYE BOLT 开槽盘头螺钉 SLOTTED PAN HEAD SCREW 圆锥滚子轴承 TAPERED ROLLER BEARING 推力球轴承THRUST BALL BEARING 平键 FLAT KEY 弹簧垫圈 SINGLE COIL SPRING WASHER 平垫圈 FLAT WASHER 螺母 FULL NYLOCK NUT 圆螺母 ROUND NUT REMOVE ALL BURRS AND SHARP EDGES 所有尖角/棱角倒角并去毛刺 40 REF 为测量的参考尺寸 OD 1/4’ outside dimension 1/4的缩写 外径直1/4’-------应该为：外径值1/4 75 CRS 尺75 材质为冷轧钢板 -------应该为：尺寸75 材质为冷轧钢板 ACCESS Accessory 附件 ADJ Adjustable,Adjust 调整 ADPT Adapter 使适应 ADV Advance 提前 AL Aluminum 铝 ALLOW Allowance 允许 LT Alternate 改变 ALY Alloy 合金 AMT Amout 数量 ANL Anneal 锻炼 ANSL Amer Natl Stds Institute APPROX Approximate 大约 ASME Amer Society of Mech Engrs ASSEM Assemble 装配 ASSY Assembly 装配 AUTH Authorized 授权的 AUTO Automatic 自动的 AUX Auxiliary 辅助的 AVG Average 平均 AWG American Wire Gauge BC Bolt Circle 螺栓圆周 BET Between 之间 BEV Bevel 斜角 BHN Brinell Hardness Number 布氏硬度值 BLK Blank ,Block 空白 B/NM Bill of Material 材料费 BOT Bottom 底部 BP or B/P Blueprint 蓝图 BRG Bearing 轴承 BRK Break 破裂 BRKT Bracket 支架 BRO Broach 钻孔 BRS Brass 黄铜 BRZ Bronze 青铜 B＆S Brown＆Shape 棕色＆形状 BSC Basic 基本的 BUSH Bushing 套管 BWG Birmingham Wire Gauge C TO C Center-to-Cente