气焊与气割器具使用安全技术交底记录.doc
文本预览下载声明
气焊与气割器具使用安全技术交底记录
气焊与气割器具使用安全技术交底记录提要:首先应检查乙炔发生器的安全装置、管路、阀门和操纵机构是否正常。确认正常后才能灌水和加入电石
安全技术交底记录编号
工程名称:***工程
施工单位:***建筑工程公司
交底提要:气焊与气割器具使用安全交底交底日期:*年*月*日
交底内容:气焊与气割器具使用安全技术交底
l.乙炔发生器使用安全要求
发生器的操作人员必须受过专门培训;熟悉发生器的结构、作用、工作原理及维护规则,并经安全部门考试合格者。
移动式乙炔发生器可安放在室外,也可安放在通风良好的室内。但严禁安放在锻工、铸工和热处理等热加工车间、正在运行的锅炉房等。
固定式乙炔发生器,必须安放在单独房间或专用棚子内。
禁止放在高压线下和吊车滑线下面o
不准靠近空气压缩机、通风机的吸口处。
不准安放在避雷针接地导体附近以及金属构件接地导线上,同对要注意,不要放在可能成为电气回路的轨道中。
放置位置还要注意防止可能来自高处的烟火、电焊火花以爱坠落工件的打击。
乙炔发生器与明火、散发火花地点、高压电源线及其他热源的距离,应不小于10m。
乙炔发生器不准安放在剧烈震动的工作台和设备上。
严禁在烈日下暴晒。
2.使用前准备工作的要求
首先应检查乙炔发生器的安全装置、管路、阀门和操纵机构是否正常。确认正常后才能灌水和加入电石。
灌入发生器的水,必须保证没有任何油污或其他杂质的洁净水,同时要按规定灌足小量,及时排出气室积存的灰渣,每班应补充或换新水,保证气室内冷却良好。
装入的电石量和粒度,一定要符合乙炔发生器的规定和要求。移动式乙炔发生器所使用的电石粒度,一般在25-80mm范围内。如果电石反应区有排热装置时,允许添加不超过5%的粒度为2--25ram的电石。大型电石入水式乙炔发生器。其电石粒度亦应在8-80mm范围内,2-8mm的电石不应超过30%。电石粒度大于80mm不得使用,否则容易产生塔桥卡料.新装人电石后,应先排放发生器内及管道留存的乙炔-空气混合体。
乙炔发生器发生冻结时,只能用蒸汽或热水解冻,严禁用明火或烧红的铁烘烤,更不准用铁器等易产生火花的物体敲击。
乙炔发生器内的活动部件,不得与器内其他结构摩擦、碰撞而产生火花。
禁止使用浮筒式乙炔发生器。
审核人***交底人***接受交底人
本表由施工单位填写井保存.
Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full
显示全部