M-10D参数(中文).doc

0000 INI LSK TVC 08 0 TVC :TVC CHECK 0:不实行 1:实行 1 LSK :LABEL SKIP 0:OFF 1:ON 2 3 4 5 INI :入力单位(用TAPE的G20,G21来变化) 0:mm输入 1:INCH输入 6 7 0001 RMVx SCAl MI 08 0 MIRx:各轴的Mirror Image 设定 0: Mirror Image off(normat) 1 Mirror Image on (mirror) 在ndinr请勿使用 1 SCLx:设定各轴的Scaling的有效无效 0:无效 1:有效 2 3 4 5 6 7 RMVx设定各轴的控制轴的取下(非setting) 0:不取下控制轴 1: 取下控制轴 0002 MLK DLK MABS OVC SBK BDT1 DRN AFL 08 0 AFL:补助机能Lock 0:off 1:on 1 DRN:DRY RUN 0:off 1:on 2 BDT1:operational Block skip 0:off 1:on 3 SBK:single Block 0:off 1:on 4 OVC:over ride cancel 0:off 1:on 5 MABS:Manual Absolute 0:off 1:on 6 DLK:Display lock 0:off 1:on(锁住现在位置画面的相对坐标) 7 MLK:机械锁住 0:off 1:on 0003 BDT9 BDT8 BDT7 BDT6 BDT5 BDT4 BDT3 BDT2 08 0 BDT2:operational Block skip 0:off 1:on 1 BDT3 operational Block skip 0:off 1:on 2 BDT4 operational Block skip 0:off 1:on 3 BDT5 operational Block skip 0:off 1:on 4 BDT6 operational Block skip 0:off 1:on 5 BDT7 operational Block skip 0:off 1:on 6 BDT8 operational Block skip 0:off 1:on 7 BDT9 operational Block skip 0:off 1:on 0004 NMCL ZCAN OSTP CHG HSKP ABS 08 0 ABS:0:Incremental模式 1: Absolute模式 1 HSKP:0:Header机能有效 1:Header机能skip(无效) 2 CHG:0:off 1:on 3 OSTP:0:operation stop(从前的brand stop)off 1 :operation stop(从前的brand stop)on 4 ZCAN: 0:Z轴指令有效 1:Z轴指令取消(无效)但是Maunal有效 5 NMCL:0:ND用机械锁无效 1:ND用机械锁有效 6 7 0005 L-AL H-AL G-AL F-AL E-AL D-AL C-AL B-AL 08 0 B-AL:Baddress 0:有效 1:无效 1 C-AL:Address 0:有效 1:无效 2 D-AL:Dddress 0:有效 1:无效 3 E-AL:Eddress 0:有效 1:无效 4 F-AL:Fddress 0:有效 1:无效 5 G-AL:Gddress 0:有效 1:无效 6 H-AL:Hddress 0:有效 1:无效 7 L-AL:Lddress 0:有效 1:无效 0006