基于单片机与12864液晶的万年历_c语言程序.pdf

#includereg52.H #includeintrins.h #includemath.h ////////////////////////////////////////DS18B20 #defineucharunsignedchar #defineuint unsignedint sbitDQ= P1^0; // 定义DS18B20的单总线 #defineLcd_Bus P0 sbitLCD_RS=P2^7; //数据/命令选择 sbitLCD_RW=P2^6; //读写控制 sbitLCD_EN=P2^5; //片选信号 #defineLCD_DATAP0 //8bit 数据线 #defineLOW 0 #defineHIGH 1 //初始化指令 #defineCLEAR_SCREEN 0x01 //清屏指令：清屏且AC值为00H #defineAC_INIT 0x02 //将AC设置为00H。且游标移到原点位置 #defineCURSE_ADD 0x06 //设定游标移到方向及图像整体移动方向（默认游标右移，图 像整体不动） #defineFUN_MODE 0x30 //工作模式：8位基本指令集 #defineDISPLAY_ON 0x0c //显示开,显示游标，且游标位置反白 #defineDISPLAY_OFF 0x08 //显示关 #defineCURSE_DIR 0x14 //游标向右移动:AC=AC+1 #defineSET_CG_AC 0x40 //设置AC，范围为：00H~3FH #defineSET_DD_AC 0x80 #defineFUN_MODEK 0x36 //扩展指令集，8位指令 #defineX1address 0x80 //上半屏X轴起始地址 #defineX2address 0x88 //下半屏X轴起始地址 #defineYaddress 0x80 //Y轴起始地址 #define Set_Column 0x40 #define Set_Page 0xB8 ucharcodeshu[]={0x30,0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39}; ucharcodexingqi[]=星期; ucharcodehanzishu[]=一二三四五六日; unsignedcharTempData= 0; double DS18B20Data; uintjiemian=0; //////////////////////////////////////////DS1302 sbitDS1302_RST=P1^4; sbitDS1302_IO = P1^3; sbitDS1302_SCK =P1^2; unsigned char table[]={0X00,0X18,0X0c,0X15,0X06,0X01,0X0a};//0s 24min 12hour 14ri 5yue 5zhou 2010nian unsignedchardatatable1[7]; //ucharcodetable2[]={0x30,0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39}; ucharcode shuzi[]={ 0x00, 0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,0x0a, 0x0b,0x0c,0x0d,0x0e,0x0f,0x10,0x11,0x12,0x13,0x14, 0x15,0x16,0x17,0x18,0x19,0x1a,0x1b,0x1c,0x1d,0x1e, 0x1f,0x20,0x21,0x22,0x23,0x24,0x25,0x26,0x27,0x28, 0x29,0x2a,0x2b,0x2c,0x2d,0x2e,0x2f,0x30,0x31,0x32,